Online Multi-parameter Water Quality Sensor
Model
W4000
Online Multi-parameter Water Quality Sensor dari perusahaan kami yang dilengkapi dengan sistem wiper terintegrasi merupakan solusi praktis untuk pemantauan kualitas air secara in-situ di sungai, danau, aliran air, muara, maupun laut. Wiper dapat secara efektif membersihkan kotoran, gelembung udara, serta mencegah biofouling selama penggunaan instrumen dalam jangka waktu yang lama. Seluruh data kalibrasi disimpan di dalam memori sensor, dan sistem mendukung proses kalibrasi sensor di lapangan serta penggantian sensor di lapangan. Secara keseluruhan, hingga 7 parameter (6 sensor) dapat diukur secara bersamaan, meliputi DO (Dissolved Oxygen/oksigen terlarut), Konduktivitas, Kekeruhan (Turbidity), pH, ORP (Oxidation-Reduction Potential/potensial oksidasi-reduksi), Klorofil, BGA (Blue-Green Algae/alga hijau-biru), OIW (Oil in Water/minyak dalam air), dan NH4-N (amonia nitrogen).
INFORMASI PRODUK
Deskripsi Produk
DO Sensor | Interface | With waterproof connector | |
| Principle | Fluorescence method | ||
| Range | 0-20mg/L or 0-200% SAT | ||
| Accuracy | ±5% or ±0.3 NTU (Take the larger value) | ||
| Resolution | 0.01mg/L | ||
| Material | Ti | ||
| Output | RS485, MODBUS | ||
|
Conductivity (Salinity) Sensor | Interface | With waterproof connector | |
| Principle | Four electrode method | ||
| CT Range | 0.01~5mS/cm or 0.01~100mS/cm | ||
| CT Accuracy | <1% or 0.01mS/cm (Take the larger value) | ||
| SAL Range | 0~2.5ppt or 0~80ppt | ||
| SAL Accuracy | ±0.05ppt or ±1ppt | ||
| Material | Ti+PEEK+Nickel | ||
| Output | RS485, MODBUS | ||
|
Turbidity Sensor | Interface | With waterproof connector | |
| Principle | 90° scattered light | ||
| Range | 0 – 1000 NTU | ||
| Accuracy | ±5% or 0.3 NTU | ||
| Resolution | 0.01 NTU | ||
| Material | Ti | ||
| Output | RS485, MODBUS | ||
|
pH Sensor | Interface | With waterproof connector | |
| Principle | Electrode method | ||
| Range | 0-14pH | ||
| Accuracy | ±0.02pH | ||
| Resolution | 0.01 | ||
| Material | POM + Ti | ||
| Output | RS485, MODBUS | ||
|
Chlorophyll Sensor | Interface | With waterproof connector | |
| Principle | Fluorescence method | ||
| Range | 0~400 µg/L or 0~100RF | ||
| Accuracy | ±5% or 0.5?g/L (Take the larger value) | ||
| Resolution | 0.01 ?g/L | ||
| Material | Ti | ||
| Output | RS485, MODBUS | ||
| BGA Sensor | Interface | With waterproof connector | |
| Principle | Fluorescence method | ||
| Range | 0-200,000 cells/mL | ||
| Detection limit | 300 cells/mL | ||
| Linearity | R²>0.999 | ||
| Resolution | 1 cells/mL | ||
| Material | Ti | ||
| Output | RS485, MODBUS | ||
|
ORP Sensor | Interface | With waterproof connector | |
| Principle | Electrode method | ||
| Range | -999~999mV | ||
| Accuracy | ±20mV | ||
| Resolution | 1mV | ||
| Material | POM + Ti | ||
| Output | RS485, MODBUS | ||
|
OIW Sensor | Interface | With waterproof connector | |
| Principle | Fluorescence method | ||
| Range | 0-50 ppm | ||
| Accuracy | 0.01ppm | ||
| Resolution | R²>0.999 | ||
| Material | Ti | ||
| Output | RS485, MODBUS | ||
|
Other Information | Sensor body | 7 waterproof ports, support up to 6 digital sensor access, 1 central cleaning brush, probe and cleaning brush can be disassembled, free combination. | |
| Size | ?81mm *476mm | ||
| Temperature | 0~50°C | ||
| Calibration data | Calibration data is stored in the probe, which can be disassembled and taken to the laboratory for calibration. | ||
| Output | RS485, MODBUS | ||
| Automatic cleaning | Yes | ||
| Brush control | The default cleaning interval is 30 minutes But you can set the cleaning interval | ||
| Power supply | Sensor: DC 12~24V, ?1A; Single probe: 9~24V, ?1A | ||
| Protection level | IP68 | ||
| Material | POM, copper sheet | ||
| State alarm | There are voltage abnormal alarms, water leakage alarms, and self-cleaning brush abnormal alarms | ||
| Cable length | With waterproof connector, 10m (default), customizable | ||
| Protection cover | Multiparameter Sonde protection cover is standard |
